Aggregated Book
This book contains the selected papers presented at the 5th International Conference on Materials Engineering and Science (IConMEAS 2022), which was held at İstanbul Topkapı Üniversitesi, Istanbul, Turkey on August 22-23, 2022. The main objective of IConMEAS 2022 is to provide a comprehensive global forum for experts and participants from academia and industry to exchange ideas and present results of ongoing research.
Preface
Chapter 1: Properties and Treatment of Structural Metals
Using Artificial Neural Networks to Predict Hardness and Impact Toughness of Aluminum Alloy 6061-T6
Effect of Co on Microstructure and Properties of Al-30%Si Alloys
Comparative Study of the Mechanical Properties of Spot Welded Joints
Experimental Investigations of Surface Finish Generated by Wire Electrical Discharge Machining
Experimental Investigations of Hydrodynamic Deep Drawing of Galvanized Steel to Form a Hemispherical and Complex Cup
Investigation of Fatigue Behavior for Al/Zn Functionally Graded Material
Alumina Nano Powder Impact on Electrical Discharge Machining of Titanium Alloy Wire
Chapter 2: Polymers and Composites
Natural Hybrid Reinforcement Effect on Mechanical Properties of UPE Composite
Developing Crumbed Rubber Tires / Epoxy Composite, by Surface Treatment with Different Silane Coupling Agents
Numerical and Experimental Study of Multi-Layer Armors for Personal Protection
Hardness and Dry Sliding Wear Characterization of Functionally Graded Materials Employing Centrifugal
The Effect of Filler and Fiber Type on the Behavior of Body Armor Composite
Enhancement Mechanical, Thermal and Dielectrical Characteristics of Polystyrene Reinforcement by Glass Fiber and Additive Kaolin
Enhancement the Crashworthiness Parameters Using Natural and Hybrid Composites under Axial Static Crushing
Enhancement Mechanical Properties of Polymers Reinforcing by Nano Graphene
The Compatibility Characterization of PMMA/DPET Based Polymer Blend
Improvement of Tensile and Flexural Properties of Fiber Pre-Stressing Composite by Using Nano Graphene
Chapter 3: Protective Coatings
Study the Fatigue Corrosion Behavior of Turbine Blade by Laser Cladding
The Physical-Mechanical Properties in Aggressive Media of Epoxy Composite Reinforced with Waste Glass Materials
Effect of Multi-Walled Carbon Nanotubes (MWCNTs) in Reducing the Corrosion Rate in Cr-MWCNTs Composite Coatings
The Influence of Thermo Mechanical Treatment on Corrosion Resistance of Cu-Al-Ni Shape Memory Alloy
Boriding Treatment of Low Alloy Steels: Effect of Holding Time and Temperature
Indirect Production of Chromium Carbides Film on Low Alloy Steel
Characterization of Functional Polyphenylsilsesquioxane (PhSiO3/2) Hybrid Glass Reinforced with MWCNTs
Chapter 4: Laser Processing Technologies
One-Step Fabricate of Copper Nanoparticles via Pulsed Laser Ablation in Liquid: Influence of Energies on Physical Characterization
Optimization of CO2 Laser Parameters for Hole Micro Drilling of PMMA: An Experimental and Theoretical Study
Multiple-Response Optimization of Aluminum Oxide Nanocoating Prepared by Pulsed Laser Deposition Using Taguchi Design
Chapter 5: Materials for Optoelectronics, Electronics and Energy Storage
Absorption Spectrum and Raman Spectroscopy of Coumarin507 Dye Laser in Different Solvents
Morphological and Optical Study of Black P- Silicon Textured in KOH Bath
In2O3/MoS2/Reduced Graphene Oxide Nanostructure as Composite Electrodes for Supercapacitors
Structural Morphological and Optical Investigations of Nano Silver Oxides Nanostructures
Dielectric, AС Conductivity and Optical Characterizations of (PVA-PEG) Doped SrO Hybrid Nanocomposites
Characterization of Zinc Oxide Semiconductor Thin Film Treated with Cold Plasma
Conductivity Modification of ZnO NRs Films via Gold Coating for Temperature Sensor Application
Chapter 6: Materials for Biomedical Application
The Biomedical Investigation of Bioceramic Cordierite as Orthopedic Material
Surface Enhancement of Magnesium Implants for Long Term Applications
Comparing the Mechanical Behavior of Lamination Resin Reinforced with Two Types of Organic and Inorganic Particles Used in Prosthetic Applications
A Review of some Characteristics of a Composite Hybrid Socket for Prosthetics Derived from Plant Fibers
Mechanical Properties of Hybrid Composites PMMA Denture Base with Varying Concentrations of Nano-ZrO2 and Glass Fiber
Deposition of Layered Bioceramic HA/TiO2 Coatings on Ti-6Al-7Nb Alloys Using Micro-Arc Oxidation
Preparation of Bio-Composite Coatings on Titanium Substrate by Electrostatic Spray Deposition
Antireflective and Hard Multicoat Design for Allyl Diglycol Carbonate Plastic Spectacle Lenses
Boosted Antimicrobial and Self-Cleaning Activities with MnO2/ ZnO Coated on Cotton Fabric
Preparation and Characterization of an Electrospun Polycaprolactone/Polyurethane Scaffold for Soft Tissue Applications
Mechanochemical Synthesis of Dendrimers as Nanocarriers: A Review
Chapter 7: Technologies of Chemical Production
Novel Study of Surface Morphological Properties of Commercial Catalytic Reforming Catalysts Used in Iraqi Refineries by Atomic Force Microscopy (AFM)
Crystallization by Acid Hydrolysis-Sulfonation of Cellulose Nanofibers from Eichhornia crassipes
Chapter 8: Environmental Protection and Bio-Based Building Materials
Computational and Experimental Simulation of Pollutant Transport through Multiple Porous Media
Preparation of Mixed Matrix Membranes Containing COF Materials for CO2 Removal from Natural Gas/Review
Construction of Magnetic Z-Scheme P-Doped Biobr/CoFe2O4 Nanocomposite for Expeditious Visible Light Photocatalytic Palm Oil Mill Effluent Degradation via the Assistance of IO4- and S2O82-
A Review on Self-Healing Concrete
| Erscheinungsdatum | 17.05.2023 |
|---|---|
| Reihe/Serie | Scientific Books Collection |
| Sprache | englisch |
| Maße | 170 x 240 mm |
| Gewicht | 990 g |
| Themenwelt | Medizin / Pharmazie ► Allgemeines / Lexika |
| Naturwissenschaften ► Physik / Astronomie ► Atom- / Kern- / Molekularphysik | |
| Technik ► Maschinenbau | |
| Schlagworte | alloy • Aser Cladding • biomaterials • Coating • composite • Concrete • Deep Drawing • environmental protection • Hardness • Laser processing • mechanical properties • Nanocomposite • nanomaterials • Polymer • steel • Thin film • Wire Electrical Discharge machining |
| ISBN-10 | 3-0364-0100-8 / 3036401008 |
| ISBN-13 | 978-3-0364-0100-3 / 9783036401003 |
| Zustand | Neuware |
| Informationen gemäß Produktsicherheitsverordnung (GPSR) | |
| Haben Sie eine Frage zum Produkt? |
aus dem Bereich
