Mechatronics and Mechanical Engineering I
Trans Tech Publications Ltd (Verlag)
978-3-03835-292-1 (ISBN)
Collection of selected, peer reviewed papers from the 2014 International Conference on Mechatronics and Mechanical Engineering (ICMME 2014), September 6-8, 2014, Chengdu, China. The 78 papers are grouped as follows:
Chapter 1: Advanced Materials Engineering and Processing Technologies;
Chapter 2: Applied Mechanics and Mechanical Engineering;
Chapter 3: Applied Thermal Research;
Chapter 4: Instrumentation and Measurement Technologies;
Chapter 5: Electrical and Electronic Engineering;
Chapter 6: Mechatronics and Robotics;
Chapter 7: Bio and Medical Research
Preface and Committees
Chapter 1: Advanced Materials Engineering and Processing Technologies
Effects of Non-Equilibrium Solidification and Aging Treatment on Microstructure Characteristic of a Ni-Base Superalloy
An Experimental Investigation on the Mechanical Properties of Glass Fiber Woven Roving Fabrics/Chopped Strand Mats Hybrid Composites Manufactured by Different Processes
Low-Fire Processing (1-x)Mg0.95Co0.05TiO3 - xCa0.6La0.8/3TiO3 Microwave Dielectric Ceramics
The Influences of Interdigitated Electrode Asymmetry on the Actuation Performance of Piezoelectric Materials
Theoretical and Experimental Analysis of Dielectric Elastomer Unimorph Cantilever
Effect of T6 Treatment on Low-Cycle Fatigue Properties of Al-6Zn-2.5Mg-2Cu-0.1Zr-0.1Sc Alloy
Preparation of Henriol C Molecularly Imprinted Polymer Microspheres
Magnetic Properties of Low Grade Manganese Carbonate Ore
A Study Surface Layer and Hardness Produced by Induction Hardened S45C Steel
Meso-Damage Theory and its Application in Research of Materials Science
The Study on Open-Celled Morphology of Polymer Blends in Vibration
Influence of Sintering Temperature on the Thermoluminescence Spectra of MgSO4 Doped with RE(Tm,Dy) and Mn
Electromagnetic Field Acting on the Scale Inhibition Experiment and Mechanism on Circulating Cooling Water of Power Plant
The Preparation and Research on Multifunctional Environmentally Friendly Corrosion Inhibitor of Chemical Cleaning
Structural and Magnetic Properties of Ni0.5Zn0.5Fe2O4 Synthesized through the Sol-Gel Method
A Framework for Conversion of Plastic Waste into Fuels and Chemicals: A Review of the Waste Current Situation in Libya
Chapter 2: Applied Mechanics and Mechanical Engineering
Effect of Blade Inclining Angle on Internal Characteristic of Hydraulic Retarder
Impact Toughness Influence on the Bending Properties of Rock Bolt
Research on Structural Optimization Method of Rack and Pinion Steering Gear with Variable Ratio
Dynamics of Scratch Drive Actuators during Stepwise Motion
Design Optimization and Analysis of NACA 0012 Airfoil Using Computational Fluid Dynamics and Genetic Algorithm
A Study of Laser Aided Activating TIG Welding
Experimental Study on the Determinants of Surface Finish in Automated Polishing of Moulds
Autodyn-2D Simulation of Shaped Charge Jet Formation and Penetration Mechanism into Multi-Layered Shielded Target
Minimizing Axial Energy Loss by Using Vane Turbine in the Propeller Slipstream
Research on the Optimal Disc Cutter Spacing for Rock-Breaking Based on ANSYS
Application of Fault Diagnosis Method Based on cICA to Gearbox
Experimental and Numerical of Sloshing Effect on Heave and Pitch Motions of FLNG Vessel
Analysis on Stability of POGO and Parameters of Propulsion System in Liquid Rocket
Mathematical Simulation and Design Optimization of a Novel Swing Vane Compressor
Rotor-Dynamic Characteristic Evaluation of Generator Geothermal Power Plant Using Finite Element Method
Theoretical Analysis on the Ultimate Bearing Capacity for Steel Tubular Transmission Tower’s Joints with Annular Plate
Chapter 3: Applied Thermal Research
A New Flow Safety Assessment Method for Direct-Heater Used in Heat Transportation of Waxy Crude Pipeline
Study on the Combustion Characteristic of Adhesive Polystyrene
Experimental Study on Downward Flame Spread of Rigid Polyurethane Foam with External Radiation
Effect of Sample Width on Downward Flame Spread over Typical Energy Conservation Material at a High Elevation Area
Fitness for Service Assessment of High Pressure Heater Tube at Coal Fired Power Plant
A Relationship between Flash Point and Boiling Point of the Flammable Liquids at Low Pressure
The Physical Properties (Enthalpy and Thermal Conductivity) of Mahogany Wood Induced by Pyrolysis Temperature Process
The Effect of Percentage of CO2 on the Biogas Counterflow Diffusion Flame Stability
Inert Effects on Flammability Limits and Flame Propagation of LPG by CO2
Flame Stability of Gaseous Fuel Combustion inside Meso-Scale Combustor with Double Wire Mesh
Ground Moisture Condensation around the GSHP Borehole
Accounting for “Zero Curtain” Effect in GSHP Simulation
The Influence of Subway’s Underground Facilities Operation on the Natural Thermal Conditions of Adjacent Soil
Technical and Economic Aspects of Using Heat Pump Systems for Heating and Cooling of the Moscow Subway's Facilities
Chapter 4: Instrumentation and Measurement Technologies
Digital Measurement and its Error Analysis for the Machining Free-Form Surface
Research on Magnetoelectric Seismometer's Low Frequency Extension Technology
Optical Computer Mouse Referenced Calibration of an Inertial Measurement Unit for Use in Unmanned Underwater Vehicles
A New Dielectric Elastomer Sensor Based on Cantilever Beam Structure with Constant Strength
Numerical Analysis of the Failure Modes for the Circular Dielectric Elastomer Actuator
Study of On-Line Detection of Voltage Transient Disturbance Based on DSP and Wavelet
Design and Development of a Multifunctional Flight Display System
Attitude Measurement Low Frequency Error Identification and Compensation for Star Tracker with Gyros
Measurement of Polycrystalline Diamond Craters in Electrical Discharge Machining
Chapter 5: Electrical and Electronic Engineering
Comparative Research of 240-Coil Permanent Magnetic Brushless Motor with or without Potting Compound
Application Analysis of Expanded Conductor in 1000kV UHV Double-Circuit Line
Stability Analysis of the AC Filter Capacitor Structure
Design for Drive Circuit of Solid Micro-Thruster Ignition System
An Automation Methodology for Modeling Posynomial Equations for Use in CMOS OpAmp Synthesis
Enhancing Vibration Damping of Smarts Structures by Energy Transfer between Modes
Chapter 6: Mechatronics and Robotics
Position Equation Establishment and Kinematics Analysis of 3-RRC Parallel Mechanism
An Application on Medical Tele-Diagnosis Robot (MTR) for Real-Time Motion Detection
A Fault Detection Method Based on Feedforward Compensation in Mechatronic Control System
A 3D Sequential LiDAR Data Registration Method for Unmanned Ground Vehicle
Design Optimisation and Analysis of a Quadrotor Arm Using Finite Element Method
Chapter 7: Bio and Medical Research
A Novel Methodology to Assess the Relaxation Rate of the Intervertebral Disc by Increments on Intradiscal Pressure
Research on the Biodegradable Buffer PFFM
The Anti-Inflammatory Effects of Leptochloa Paste for External Use
Study of Fe(II) Biosorption Using Pleurotus Spent Mushroom Compost in a Fixed-Bed Column
Effect of Sophora Japonica Total Flavonoids on Mouse Models of Hyperglycemia and Diabetes Model
The Investigation of the Interaction between Daidzin and Bovine Serum Albumin by Fluorescence Spectroscopy
Qumai Total Flavonoids Induced Diabetic Mice Model of Streptozotocin
Biogas Purification Using Natural Zeolite and NaOH
Automatic Bone Drilling in Orthopedic Surgery - Overcoming of the Drill Bit Bending at the Second Cortex
Prosthesis Design for Bilateral Hip Disarticulation Management
The Research of Topical Analgesic Effect on Arisaema Wine Paste, Vinegar Paste
Study on the Vacuum Drying Model of Perilla Leaf by Microwave Method
| Reihe/Serie | Applied Mechanics and Materials |
|---|---|
| Zusatzinfo | Illustrations, unspecified |
| Verlagsort | Zurich |
| Sprache | englisch |
| Maße | 170 x 240 mm |
| Gewicht | 930 g |
| Themenwelt | Technik ► Maschinenbau |
| ISBN-10 | 3-03835-292-6 / 3038352926 |
| ISBN-13 | 978-3-03835-292-1 / 9783038352921 |
| Zustand | Neuware |
| Haben Sie eine Frage zum Produkt? |
aus dem Bereich
