Mechanical and Electrical Technology VI
Trans Tech Publications Ltd (Verlag)
978-3-03835-205-1 (ISBN)
Collection of selected, peer reviewed papers from the 2014 6th International Conference on Mechanical and Electrical Technology (ICMET 2014), July 17-18, 2014, Bangkok, Thailand.
The 71 papers are grouped as follows:
Chapter 1: Thermal and Mechanical Research, General Mechanical Engineering,
Chapter 2: Tools and Electrical Engineering,
Chapter 3: Mechatronics and Robotics,
Chapter 4: Control and Automation,
Chapter 5: Information Technologies, Data and Signal Processing,
Chapter 6: Industrial Engineering
Preface, Committees and Sponsors
Chapter 1: Thermal and Mechanical Research, General Mechanical Engineering
Prediction the Springback in Air-Bending Process Using Neural Network Metamodel
Dynamic Equilibrium Configurations of Multibody Systems
Wear Behaviour of Stellite 6 Coatings Produced on an Austenitic Stainless Steel Substrate by Laser Cladding Using Two Different Heat Inputs
Influence of Pipe Diameters on Shapes of Air Taylor Bubbles in Small Pipes Containing Stagnant Water
On the Use of Composite-Steel Joint for Semi-Monocoque Frame Design
Influence of Blast Wave on Behavior of Steel Plate
The New Rolling Mill Gearbox Concept Design
Numerical Analysis for Resistance Calculations of NPL as a Floating Hull for Wave Glider
Design of a Simple Underactuated Mechanical Gripper
Evaluation of the Performance of Micro-Drills in Drilling a Machinable Ceramic Material
Parametric Optimization in Turning of CFRP (Epoxy) Composites: A Case Experimental Research with Exploration of HS Algorithm
NET3D Calculation on the Depth of Penetration by a Long-Rod Penetrator with Varying Obliquity
Simulation on the Life Expectancy of Fine Blanking Punch for Recreation Vehicle Seat Recliner Sector Tooth
Utilization of Tooth Contact Pattern in a Gear Meshing Model for Estimation of Sliding Loss in a Parallel-Axis Gear Pair
Field Investigation on Thermal Performance of the Tile Ventilator
Computer Aided Design of the Die-Set for Sheet Metal Punching and Blanking Dies
A Hybrid Approach for Process Optimization in Taper Cutting Operation Using Wire Electrical Discharge Machining
Optimization of the EDM Parameters on Machining Ti-6Al-4V Alloy with Multiple Quality Characteristics
Transient Radiation Coupled With Conduction Heat Transfer in a One Dimensional Slab
Thermodynamic Analysis of Hydrogen Production from Methanol Reforming in Supercritical Water
A CAPP/CAD for Sheet Metal Deep Drawing
The Effect of Rise Angle of V-Hull Non Ballast Ship on Resistance Performance
Synthesis of Rigid-Body Guidance Mechanism with Path and Pose Generation Independently
The Effects of Injection Timing on BDF in an IDI Diesel Engine
Heat Transfer Enhancement due to V-Shaped Perforated Blocks in a Solar Air Heater Duct
The Performance of the Interlocking Block Solar Collector
SOx Reduction by Feedwater in an Industrial Boiler
Chapter 2: Tools and Electrical Engineering
Development of an Oscillating Drum Granulator Prototype for Cassava Pearl
Optimization of the Thrust Ripple of a Tubular Flux-Switching Permanent Magnet Linear Motor
Design, Fabrication and Evaluation of a Novel Electro Thermal Micro-Gripper for Handling of Head Gimbal Assembly
2x2 Rectangular-Slot Microstrip Array Antenna for WLAN Applications
An Effective Implementation of the Nonlinear Homotopy Method for MOS Transistor Circuits
Parallel-Connected High Voltage Multiplier with Symmetrical Structure
Electrical Energy Conservation in Engineering Industry: A Case Study
Space Frame Analysis, Design, and Testing for Electric Vehicle Formula
Effect of Grain Size on Effective Permittivity of Ferroelectric Films Based on Effective Medium Theory
Chapter 3: Mechatronics and Robotics
Mechanism Design and Manipulating Algorithm for Orientation Changing Module with Three Flexible Links
An Innovative Motion Planning for 4-DOF PKM
An Altitude Estimation Technique for Autonomous Landing of a Quad-Rotor Using a Vision System
Dexterity Measures for 4DOF Exoskeleton Robot
Weld Bead Tracking Control of a Magnetic Wheel Wall Climbing Robot Using a Laser-Vision System
Implementing Expandable Path for an Resizable Cobot
A μP-μC-FPGA Synergy Controller for a Linear Delta Robot
The Performance of a Delta Telerobot
Design Morphological Changing All-Terrain-Rover and Optimizing with Genetic Algorithm for Enhancing Mobility
A Low-Cost Stereo Vision System for Real-Time Pose Estimation and its Application for Robot Tracking
A Study on Mobile Gait Rehabilitation Training Robots
Chapter 4: Control and Automation
A Weighting Slope MPPT Method Based on Sun Tracking Applied in PV System
Experiment of the State Variable Feedback for a Quadrotor
Vibration Rejection and Stabilization Control for an Inertial Stabilization System
Study on Dynamic Characteristics of DC Valve in Electro-Hydraulic System Using CFD Simulation
Gain-Scheduled Control Approach by Logarithm Transformation for Electrical Vehicle Traction Force Control
Evaluation of Deadband Effect in Steer-by-Wire Force Feedback System by Using Driving Simulator
A New Stator Flux Estimation Method for Direct Torque Control of Electrical Excitation Flux-Switching Generator
Tracking Control for the Center-of-Gravity Constant Shift of Omnidirectional Rehabilitative Training Walker
Process Control Virtual Laboratory: Temperature Control Based on LabVIEW for Convection Heat Transfer
Chapter 5: Information Technologies, Data and Signal Processing
Improved SPIHT Algorithm for Texture Image Compression
10.3125Gbps High-Speed SFP+ Channel Signal Integrity Evaluations
A New Analytical Approach to Estimate Fading in Mobile Communication System Design
Driver Behavior Detection Based on Multi-GNSS Precise Point Positioning Technology
Complex Network Based Modeling and Analysis of Resource Nodes for MG
Evaluating the III-Posedness of Inverse Problem to Size Flaws from Eddy Current NDT Signals Obtained with an Absolute Type Probe
Low-Complexity Multiplication Using Complement and Signed-Digit Recoding Methods
Comparative Study on Wear Particle Colour Classifications Using Various Machine Learning Algorithms
Design and Implementation of Linux-Based Supervisory and Control Configuration Software for Automatic Billet Cut-to-Length System
Chapter 6: Industrial Engineering
Modeling for Materials and Logistics Optimal System in JIT Flexible Manufacturing
A Study of a Single-Period Model for the Parallel Fleet Replacement Problem
Eco-Driving Rating Based on Average Trip Speed and Evaluation
Palm Oil EFB: Green Energy Source in Malaysia
Applying Kalman Filter for Correlated Demand Forecasting
Fuzzy-TOPSIS for Appropriate Site Selection for Establishing a Thermal Power Plant
| Erscheint lt. Verlag | 22.10.2014 |
|---|---|
| Reihe/Serie | Applied Mechanics and Materials |
| Zusatzinfo | Illustrations, unspecified |
| Verlagsort | Zurich |
| Sprache | englisch |
| Maße | 170 x 240 mm |
| Gewicht | 850 g |
| Themenwelt | Technik ► Elektrotechnik / Energietechnik |
| Technik ► Maschinenbau | |
| ISBN-10 | 3-03835-205-5 / 3038352055 |
| ISBN-13 | 978-3-03835-205-1 / 9783038352051 |
| Zustand | Neuware |
| Haben Sie eine Frage zum Produkt? |
aus dem Bereich
